#LAST N LAST WOOD FINISH MSDS HOW TO#
#LAST N LAST WOOD FINISH MSDS SKIN#
#LAST N LAST WOOD FINISH MSDS FREE#

Apply only one even coat, in the direction of the grain avoiding heavy application. If applied by roller or airless sprayer, back brush immediately to ensure penetration and to avoid an uneven finish. Application using a natural bristle brush is the preferred method. Do not apply in direct sunlight, if rain, snow, heavy dew or low temperatures below 40° F (4° C) are expected within 48 hours. Apply when air and surface temperature is between 50° F (10° C) - 90° F (32° C). Stir thoroughly before and during application. Intermix all product together before starting to avoid color variance. Buy sufficient product for the whole job. Before starting, test your color choice on a small area. If water is not absorbed, wait 30 days and re-test. 2 min., depending on climate, the surface is ready for finishing. Test wood for absorbency by sprinkling water on the surface – if water is absorbed within 30 sec. Use caution when walking on wet surfaces during application.

Application DetailsĬAUTION: Surfaces are slippery when wet.

#LAST N LAST WOOD FINISH MSDS HOW TO#

Before you start, find out how to protect yourself and your familiy by contacting the USEPA National Lead Information Hotline at -LEAD or log on to Follow these instructions to control exposure to other hazardous substances that may be released during surface preparation. Clean up carefully with a HEPA vacuum and a wet mop.

#LAST N LAST WOOD FINISH MSDS SKIN#

Wear a properly fitted, NIOSH-approved respirator and prevent skin contact to control lead exposure. EXPOSURE TO LEAD DUST OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN, PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. WARNING! If you scrape, sand or remove old paint, you may release lead dust or fumes.

#LAST N LAST WOOD FINISH MSDS FREE#

Finish should be applied within one week of preparation for horizontal surfaces (decks) and four weeks for vertical surfaces (siding), provided that the surface remains free of dirt, grease, grim and mildew. Always sand in the direction of the wood grain and remove sanding dust. Sand all cleaned wood using 80-120 grit sandpaper for vertical surfaces and 60-80 grit sandpaper for horizontal surfaces. Allow the surface to dry for 48 hours, or to have a moisture content of 18% or less before application. Power wash wood surface clean with fresh water using 500- 800 psi with the nozzle 8-12 inches away to remove cleaning solution. Do not allow solution to dry on the wood surface. Scrub surface with a hard bristle brush for 15-20 minutes to help remove mill glaze or weathering. Apply a cleaning solution of four (4) ounces of 100% powdered Tri-Sodium Phosphate (TSP) or phosphate-free substitute with one (1) quart of liquid bleach and three (3) quarts of water to the wood surfaces with a garden sprayer or a heavy nap roller cover. Spray all wood surfaces with clean water, completely wetting the wood. It does not store any personal data.All wood surfaces must be thoroughly clean, dry and free of dirt, grease, grim, mildew, mill glaze and previous coatings before application. The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. The cookie is used to store the user consent for the cookies in the category 'Performance'. This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category 'Other. The cookies is used to store the user consent for the cookies in the category 'Necessary'.

The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category 'Functional'.

The cookie is used to store the user consent for the cookies in the category 'Analytics'. These cookies ensure basic functionalities and security features of the website, anonymously. Necessary cookies are absolutely essential for the website to function properly.

Last n last wood finish msds